Steroid Recipe for Injectable Winstrol in Oil(Winny) 50mg/ml
How to Make Injectable Winstrol in Oil(Winny) 50mg/ml
Injectable Winstrol Steroid Recipes for Male Muscle Growth
How to Make Injectable Winstrol in Oil 50mg/ml
3 18 or 20 gauge pins
2 22 gauge pins
17 ml of sesame seed oil
1 20 ml sterile glass vial or larger
1 .45 Whatman sterile syringe filter.
0.2 ml of benzyl alcohol
2 ml of guaiacol (super solvent)
2 5 or 10 ml syringes
1 Gram winstrol
1 20 ml glass vial or larger
2 3 ml syringes
Tip: This will make 20ml at 50mg/ml. Steroids Raw Powder Only attempt to convert 1 gram of winstrol powder at a time; it is very easy to destroy it during the conversion.
Steps:
Step 1 Use a scale to weigh 1 gram of winstrol powder. To weigh out your powder to 1 gram, use the tare function to subtract the weight of the container holding it.
Step 2 Using one of the 3 ml syringes, draw off 2 ml of the super solvent.
Step 3 Place the powder in the glass vial, then top it off with the super solvent.
Step 4 A:Put one of the 20g pins into the rubber stopper and replace the stopper. Put the vial in a small pan and set it on the stove's heat source (you can do this step in the oven, but I have found this method works better). Turn up the heat and cook the powder until it turns into a liquid (the melting point of winstrol is Good Quality Steroid Powder between 239.8-242 degrees F).Turn off the heat and continue to let the food cool in the pan until it reaches room temperature again, which will take about 15 minutes.Use an oven mit since the vial will be VERY HOT.
B:Sesame oil should be cooked as well (heat more than 17ml because you won't get it all out); I heated mine in the oven in a muffin tray; the oil needs to reach 212 F to help with oil sterilization. Mine was baked at 275 degrees. Just to be certain.
Step 5 Draw out ..1% of the final solution is 2 mL of benzyl alcohol.Winstrol should only be used with 1% of the solution at most; else, the program might crash.
Step 6 Add BA to the solution in the vial,Shake Glutathione with great care.
Step 7 A:Utilizing the 10 ml syringe, extract the oil (Be sure you have allowed it to cool down some) 15ml of oil should be added to the mixture. Shake one more, very lightly.
Note - After adding the oil to the solution, the winstrol may clump up again into a powder; if this happens, simply reheat it again as in Step 4a, remembering to let it cool slowly. My powder took care of it by doing this.
B: Recap the syringe after saving 2 ml of oil in it. To ensure that no winstrol is left in the filter during the subsequent sterile filtering procedure, you will require this.
Step 8 In the steile unopened vial, insert one of the 18 gauge pins, GSO/BA/BB/EO/MCT then attach the whatman sterile filter.Using the other 10ml syringe, draw out the solution, connect to the filter, and slowly force the fluid into the sterile vial.To ensure that there is no winstrol left in the filter, run the remaining 2 ml of oil through the filter using the other syringe.
Step 9 Remove the filter after filtering, leaving the pin in the sterile vial. Put the vial in a small pan and place on eye of the stove (you can do this step in the oven, but I have found this method works better). Heat the solution for 15 to 20 minutes after turning on the heat. Turn off the heat and allow it to cool until it reaches room temperature while remaining in the pan. Once more, this process takes 15 minutes.
Finished item The final U.S. raw steroids powder product should have the appearance shown below and should be a light gold color. (Unless you used grape seed oil, in which case it will be tinted green)
